Difference between revisions of "Raid:Manual Rebuild"

From SME Server
Jump to navigationJump to search
(spello)
(28 intermediate revisions by 5 users not shown)
Line 1: Line 1:
==Raid: Manual Rebuild==
 
 
{{Level|Advanced}}
 
{{Level|Advanced}}
 +
{{Warning box|Get it right or you will lose data. '''Take a backup!''' Let the raid sync, this can take quite a while.}}
  
{{Warning box|Get it right or you will lose data. Take a backup, let the raid sync}}
+
SME Servers Raid Options are largely automated, if you built your system with a single hard disk simply logon as admin and select Disk Redundancy to add a new drive to your RAID1 array. The same procedure is used if you have a disk failure in a RAID array and you have replaced that failed disk.
  
Under Re-Write
+
But with the best laid plans things don't always go according to plan, these are the processes required to do it manually.
  
SME Servers Raid Options are largely automated, if you built your system with a single hard disk, or have a hard disk failure, simply logon as ''admin'' and select ''Disk Redundancy'' to add a new drive to your RAID1 array.
+
See also: [[Hard Disk Partitioning]] and [[Raid#Resynchronising_a_Failed_RAID]]
  
 
== HowTo: Manage/Check a RAID1 Array from the command Line ==
 
== HowTo: Manage/Check a RAID1 Array from the command Line ==
 
 
=== What is the Status of the Array ===
 
=== What is the Status of the Array ===
  
Line 22: Line 21:
 
  unused devices: <none>
 
  unused devices: <none>
  
=== Are the Disk Partitioned Correctly ? ===
+
== HowTo: Reinstate a disk from the RAID1 Array with the command Line ==
  
Here two disks are partitioned identically
+
=== Look at the mdstat ===
  
[root@ ~]# '''fdisk -lu /dev/sda; fdisk -lu /dev/sdb'''
+
First we must determine which drive is in default.
 
Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
 
255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors
 
Units = sectors of 1 * 512 = 512 bytes
 
 
    Device Boot      Start        End      Blocks  Id  System
 
/dev/sda1  *          63      208844      104391  fd  Linux raid autodetect
 
/dev/sda2          208845  1953520064  976655610  fd  Linux raid autodetect
 
 
Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes
 
255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors
 
Units = sectors of 1 * 512 = 512 bytes
 
 
    Device Boot      Start        End      Blocks  Id  System
 
/dev/sdb1  *          63      208844      104391  fd  Linux raid autodetect
 
/dev/sdb2          208845  1953520064  976655610  fd  Linux raid autodetect
 
 
 
==== Example : Incorrecty Partitioned 2nd Disk ====
 
 
 
In this example the partitions are set too close to the start of the disk and there is no room for GRUB to be written, the disk will not boot, there will not be enough room for grub ''staging''
 
  
[root@ ~]# '''fdisk -l /dev/sdb; fdisk -lu /dev/sdb'''
 
 
Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes
 
255 heads, 63 sectors/track, 121601 cylinders
 
Units = cylinders of 16065 * 512 = 8225280 bytes
 
 
    Device Boot      Start        End      Blocks  Id  System
 
/dev/sdb1  *          1          13      104384+  fd  Linux raid autodetect
 
'''Partition 1 does not end on cylinder boundary.'''
 
/dev/sdb2              13      121601  976655647  fd  Linux raid autodetect
 
 
Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes
 
255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors
 
Units = sectors of 1 * 512 = 512 bytes
 
 
    Device Boot      Start        End      Blocks  Id  System
 
/dev/sdb1  *          1      208769      104384+  fd  Linux raid autodetect
 
'''Partition 1 does not end on cylinder boundary.'''
 
/dev/sdb2          208770  1953520063  976655647  fd  Linux raid autodetect
 
 
===== message Log showing Grub errors =====
 
 
add_drive_to_raid: Waiting for boot partition to sync before installing grub...
 
add_drive_to_raid: Probing devices to guess BIOS drives. This may take a long time.
 
add_drive_to_raid:
 
add_drive_to_raid:
 
add_drive_to_raid:    GNU GRUB  version 0.95  (640K lower / 3072K upper memory)
 
add_drive_to_raid:
 
add_drive_to_raid:  [ Minimal BASH-like line editing is supported.  For the first word, TAB
 
add_drive_to_raid:    lists possible command completions.  Anywhere else TAB lists the possible
 
add_drive_to_raid:    completions of a device/filename.]
 
add_drive_to_raid: grub> device (hd0) /dev/sdb
 
add_drive_to_raid: grub> root (hd0,0)
 
add_drive_to_raid:  Filesystem type is ext2fs, partition type 0xfd
 
add_drive_to_raid: grub> setup (hd0)
 
add_drive_to_raid:  Checking if "/boot/grub/stage1" exists... no
 
add_drive_to_raid:  Checking if "/grub/stage1" exists... yes
 
add_drive_to_raid:  Checking if "/grub/stage2" exists... yes
 
add_drive_to_raid:  Checking if "/grub/e2fs_stage1_5" exists... yes
 
add_drive_to_raid:  Running "embed /grub/e2fs_stage1_5 (hd0)"... failed (this is not fatal)
 
add_drive_to_raid:  Running "embed /grub/e2fs_stage1_5 (hd0,0)"... failed (this is not fatal)
 
add_drive_to_raid:  Running "install /grub/stage1 (hd0) /grub/stage2 p /grub/grub.conf "... succeeded
 
add_drive_to_raid: Done.
 
add_drive_to_raid: grub> quit
 
 
== HowTo: Remove a disk from the RAID1 Array from the command Line ==
 
 
=== Look at the mdstat ===
 
  
  [root@ ~]# cat /proc/mdstat
+
  [root@ ~]#'''cat /proc/mdstat'''
  Personalities : [raid1]
+
  Personalities : [raid1]  
md2 : active raid1 sdb2[1] sda2[0]
 
      488279488 blocks [2/2] [UU]
 
 
 
  md1 : active raid1 sdb1[1] sda1[0]
 
  md1 : active raid1 sdb1[1] sda1[0]
 
       104320 blocks [2/2] [UU]
 
       104320 blocks [2/2] [UU]
   
+
     
 +
  md2 : active raid1 sdb2[2](F) sda2[0]
 +
      52323584 blocks [2/1] [U_]
 +
     
 
  unused devices: <none>
 
  unused devices: <none>
 +
 +
(S)= Spare
 +
(F)= Fail
 +
[0]= number of the disk
 +
 +
{{note box|As we can see the partition sdb2 is in default, we can see the flag: sdb2 [2] (F). We need to resynchronize the disk sdb to the existing array md2.}}
  
 
=== Fail and remove the disk, '''sdb''' in this case ===
 
=== Fail and remove the disk, '''sdb''' in this case ===
  
  [root@ ~]# mdadm --manage /dev/md2 --fail /dev/sdb2
+
  [root@ ~]# '''mdadm --manage /dev/md2 --fail /dev/sdb2'''
 
  mdadm: set /dev/sdb2 faulty in /dev/md2
 
  mdadm: set /dev/sdb2 faulty in /dev/md2
  [root@ ~]# mdadm --manage /dev/md2 --remove /dev/sdb2
+
  [root@ ~]# '''mdadm --manage /dev/md2 --remove /dev/sdb2'''
 
  mdadm: hot removed /dev/sdb2
 
  mdadm: hot removed /dev/sdb2
  [root@ ~]# mdadm --manage /dev/md1 --fail /dev/sdb1
+
  [root@ ~]# '''mdadm --manage /dev/md1 --fail /dev/sdb1'''
 
  mdadm: set /dev/sdb1 faulty in /dev/md1
 
  mdadm: set /dev/sdb1 faulty in /dev/md1
  [root@ ~]# mdadm --manage /dev/md1 --remove /dev/sdb1
+
  [root@ ~]# '''mdadm --manage /dev/md1 --remove /dev/sdb1'''
 
  mdadm: hot removed /dev/sdb1
 
  mdadm: hot removed /dev/sdb1
  
=== Add the partitions back ===
+
=== Do your Disk Maintenance here ===
  
  [root@ ~]# mdadm --manage /dev/md1 --add /dev/sdb1
+
At this point the disk is idle.
  mdadm: hot added /dev/sdb1
+
  [root@ ~]# mdadm --manage /dev/md2 --add /dev/sdb2
+
  [root@ ~]# '''cat /proc/mdstat'''
  mdadm: hot added /dev/sdb2
+
  Personalities : [raid1]
 +
  md1 : active raid1 sda1[0]
 +
      104320 blocks [2/1] [U_]
 +
     
 +
md2 : active raid1 sda2[0]
 +
      52323584 blocks [2/1] [U_]
 +
     
 +
  unused devices: <none>
  
 +
{{note box|You'll have to determine if your disk can be reinstated at the array. In fact sometimes a raid can get out of sync after a power failure but also some times for physical outages of the hard disk. It is necessary to test the hard disk if this occurs repeatedly. For this we will use '''smartctl'''.}}
  
 +
For all the details available by SMART on the disk
  
 +
[root@ ~]# '''smartctl -a /dev/sdb'''
  
 +
At least two types of tests are possible, short (~ 1 min) and long (~ 10 min to 90 min).
  
 +
[root@ ~]# '''smartctl -t short /dev/sdb''' #short test
 +
[root@ ~]# '''smartctl -t long  /dev/sdb''' #long test
  
 +
to access the results / statistics for these tests:
  
 +
[root@ ~]# '''smartctl -l selftest /dev/sdb'''
  
 +
You can refer to this page for more information how activate or understand the Analysis and Reporting Technology (SMART) [[Monitor_Disk_Health]]
  
 +
{{Note box|if you need to change the disk due to physical failure found by the smartctl command, install a new disk of the same capacity (or more) and enter the following commands to recreate new partitions by copying them from healthy disk sda.}}
  
 +
[root@ ~]# '''sfdisk -d /dev/sda > sfdisk_sda.output'''
 +
[root@ ~]# '''sfdisk /dev/sdb < sfdisk_sda.output'''
  
 +
GPT Disks
  
===The Leadup===
+
Larger disks will be GPT Disks, sfdisk will not work - you will need to use gdisk and partx (parted)
I'm not sure if I'm reporting a bug or just some manual maintenance
+
[root@ ~]# '''yum install gdisk'''
  
My Disk didn't respond correctly to the Menu option "Manage Disk Redundancy". I was upgrading the hard disks to 1Gb disks from the 500Gb that came with the Dell server, the new disks were the Seagate 1Tb ST1000340NS, they are a Server Edition disk. It did this on both disks
+
The copy the partition table from a good disk to the new disk, the first line will copy the partition table from disk sda to sdd, the second will randomize the GUID
 +
[root@ ~]# '''sgdisk /dev/sda -R /dev/sdd'''
 +
[root@ ~]# '''sgdisk -G /dev/sdd'''
  
The Disk was installed as the 2nd Hard Disk during an Upgrade process
+
To view the partitions use partx
 +
[root@ ~]# '''partx -l /dev/sdd'''
  
''It's not fatal'', but it did stop the machine from booting on the disk, perhaps that's just ''not living, therefore not fatal'', whatever, it's not terribly useful.
 
  
 +
If you want to reinstate the same disk without replacing it, go to the next step.
  
and a look from fdisks view shows
+
=== Add the partitions back ===
  
Note the correct partitioning on sda
+
[root@ ~]# '''mdadm --manage /dev/md1 --add /dev/sdb1'''
 +
mdadm: hot added /dev/sdb1
 +
[root@ ~]# '''mdadm --manage /dev/md2 --add /dev/sdb2'''
 +
mdadm: hot added /dev/sdb2
  
[root@ ~]# fdisk -lu /dev/sda
+
=== Another Look at the mdstat ===
 
Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
 
255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors
 
Units = sectors of 1 * 512 = 512 bytes
 
 
    Device Boot      Start        End      Blocks  Id  System
 
/dev/sda1  *          63      208844      104391  fd  Linux raid autodetect
 
/dev/sda2          208845  1953520064  976655610  fd  Linux raid autodetect
 
  
What has happened here is the disk partition has been written too close to the start of the drive, so the boot record hasn't got enough room for its GRUB staging - if thats the right term.
+
[root@sme8-64-dev ~]# cat /proc/mdstat
 
+
Personalities : [raid1]
To correct this, remove the disk from the array, you will need to fail it, then remove it, the repartition and add it back to the array
+
md1 : active raid1 sdb1[1] sda1[0]
 
+
      104320 blocks [2/2] [UU]
{{Note box|I'm using sdb which was right for me, it might not be for you (if it's RAID 1, there is a 50% chance it's not !)}}
+
     
 
+
md2 : active raid1 sdb2[2] sda2[0]
===Here we go lets fix this===
+
      52323584 blocks [2/1] [U_]
 
+
      [>....................]  recovery = 1.9% (1041600/52323584) finish=14.7min speed=57866K/sec
 
 
====Re-Partition, first clean the old partitions====
 
 
 
[root@ ~]# fdisk /dev/sdb
 
 
   
 
   
  The number of cylinders for this disk is set to 121601.
+
  unused devices: <none>
There is nothing wrong with that, but this is larger than 1024,
 
and could in certain setups cause problems with:
 
1) software that runs at boot time (e.g., old versions of LILO)
 
2) booting and partitioning software from other OSs
 
    (e.g., DOS FDISK, OS/2 FDISK)
 
 
Command (m for help): p
 
 
Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes
 
255 heads, 63 sectors/track, 121601 cylinders
 
Units = cylinders of 16065 * 512 = 8225280 bytes
 
 
    Device Boot      Start        End      Blocks  Id  System
 
/dev/sdb1  *          1          13      104384+  fd  Linux raid autodetect
 
Partition 1 does not end on cylinder boundary.
 
/dev/sdb2              13      121601  976655647  fd  Linux raid autodetect
 
 
Command (m for help): d
 
Partition number (1-4): 1
 
 
Command (m for help): d
 
Selected partition 2
 
 
Command (m for help): w
 
The partition table has been altered!
 
 
Calling ioctl() to re-read partition table.
 
Syncing disks.
 
 
 
====Then Create the new partitions====
 
Note: change the partitions system id to reflect Linux raid autodetect
 
  
[root@ ~]# fdisk /dev/sdb
+
{{note box|with a new disk it may be worthwhile to reinstall grub to avoid problems on startup error. The grub is the program that allows you to launch the operating systems. Please enter the following commands. }}
 
The number of cylinders for this disk is set to 121601.
 
There is nothing wrong with that, but this is larger than 1024,
 
and could in certain setups cause problems with:
 
1) software that runs at boot time (e.g., old versions of LILO)
 
2) booting and partitioning software from other OSs
 
    (e.g., DOS FDISK, OS/2 FDISK)
 
 
Command (m for help): n
 
Command action
 
    e  extended
 
    p  primary partition (1-4)
 
p
 
Partition number (1-4): 1
 
First cylinder (1-121601, default 1):
 
Using default value 1
 
Last cylinder or +size or +sizeM or +sizeK (1-121601, default 121601): 13
 
 
Command (m for help): n
 
Command action
 
    e  extended
 
    p  primary partition (1-4)
 
p
 
Partition number (1-4): 2
 
First cylinder (14-121601, default 14):
 
Using default value 14
 
Last cylinder or +size or +sizeM or +sizeK (14-121601, default 121601):
 
Using default value 121601
 
 
Command (m for help): m
 
Command action
 
    a  toggle a bootable flag
 
    b  edit bsd disklabel
 
    c  toggle the dos compatibility flag
 
    d  delete a partition
 
    l  list known partition types
 
    m  print this menu
 
    n  add a new partition
 
    o  create a new empty DOS partition table
 
    p  print the partition table
 
    q  quit without saving changes
 
    s  create a new empty Sun disklabel
 
    t  change a partition's system id
 
    u  change display/entry units
 
    v  verify the partition table
 
    w  write table to disk and exit
 
    x  extra functionality (experts only)
 
 
Command (m for help): a
 
Partition number (1-4): 1
 
 
Command (m for help): p
 
 
Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes
 
255 heads, 63 sectors/track, 121601 cylinders
 
Units = cylinders of 16065 * 512 = 8225280 bytes
 
 
    Device Boot      Start        End      Blocks  Id  System
 
/dev/sdb1  *          1          13      104391  83  Linux
 
/dev/sdb2              14      121601  976655610  83  Linux
 
 
Command (m for help): t
 
Partition number (1-4): 1
 
Hex code (type L to list codes): fd
 
Changed system type of partition 1 to fd (Linux raid autodetect)
 
 
Command (m for help): t
 
Partition number (1-4): 2
 
Hex code (type L to list codes): fd
 
Changed system type of partition 2 to fd (Linux raid autodetect)
 
 
Command (m for help): p
 
 
Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes
 
255 heads, 63 sectors/track, 121601 cylinders
 
Units = cylinders of 16065 * 512 = 8225280 bytes
 
 
    Device Boot      Start        End      Blocks  Id  System
 
/dev/sdb1  *          1          13      104391  fd  Linux raid autodetect
 
/dev/sdb2              14      121601  976655610  fd  Linux raid autodetect
 
 
 
Command (m for help): w
 
The partition table has been altered!
 
 
Calling ioctl() to re-read partition table.
 
Syncing disks.
 
  
 +
== HowTo: Write the GRUB boot sector ==
  
====and lastly, write the boot sector====
+
{{Warning box|as the dd command is named "data destroyer" you need to be extremely prudent and sure of the name of source partition and/or destination. At first you should skip the dd command, Step 1 below, and attempt to install grub without it, see Step 2 below. If grub can be installed without using dd, then Step 1 can be discarded. }}
  
  [root@ ~]# grub
+
*1.dd
 +
  [root@ ~]# '''dd if=/dev/sda1 of=/dev/sdb1'''
 +
*2.grub
 +
[root@ ~]# '''grub'''
 
   
 
   
 
     GNU GRUB  version 0.95  (640K lower / 3072K upper memory)
 
     GNU GRUB  version 0.95  (640K lower / 3072K upper memory)
Line 305: Line 143:
 
     completions of a device/filename.]
 
     completions of a device/filename.]
 
   
 
   
  grub> device (hd0) /dev/sdb
+
  grub> '''device (hd0) /dev/sdb'''
 
   
 
   
  grub> root (hd0,0)
+
  grub> '''root (hd0,0)'''
 
   Filesystem type is ext2fs, partition type 0xfd
 
   Filesystem type is ext2fs, partition type 0xfd
 
   
 
   
  grub> setup (hd0)
+
  grub> '''setup (hd0)'''
 
   Checking if "/boot/grub/stage1" exists... no
 
   Checking if "/boot/grub/stage1" exists... no
 
   Checking if "/grub/stage1" exists... yes
 
   Checking if "/grub/stage1" exists... yes
Line 317: Line 155:
 
   Running "embed /grub/e2fs_stage1_5 (hd0)"...  16 sectors are embedded.
 
   Running "embed /grub/e2fs_stage1_5 (hd0)"...  16 sectors are embedded.
 
  succeeded
 
  succeeded
   Running "install /grub/stage1 (hd0) (hd0)1+16 p (hd0,0)/grub/stage2 /grub/grub.conf"... succeeded
+
   Running "install /grub/stage1 (hd0) (hd1)1+16 p (hd0,0)/grub/stage2 /grub/grub.conf"... succeeded
 
  Done.
 
  Done.
 
   
 
   
  grub> quit
+
  grub> '''quit'''
 
 
and then I can use the wiki's proceedure to grow the disk - which is why I am here
 
 
 
David Bray
 
 
 
17 March, 2010
 
  
<!-- noinclude>[[Category:Howto]]</noinclude -->
+
<noinclude>
 +
[[Category:Howto]]
 +
[[Category:Administration:Storage]]
 +
</noinclude>

Revision as of 21:04, 11 February 2019

PythonIcon.png Skill level: Advanced
The instructions on this page may require deviations from standard procedures. A good understanding of linux and Koozali SME Server is recommended.


Warning.png Warning:
Get it right or you will lose data. Take a backup! Let the raid sync, this can take quite a while.


SME Servers Raid Options are largely automated, if you built your system with a single hard disk simply logon as admin and select Disk Redundancy to add a new drive to your RAID1 array. The same procedure is used if you have a disk failure in a RAID array and you have replaced that failed disk.

But with the best laid plans things don't always go according to plan, these are the processes required to do it manually.

See also: Hard Disk Partitioning and Raid#Resynchronising_a_Failed_RAID

HowTo: Manage/Check a RAID1 Array from the command Line

What is the Status of the Array

[root@ ~]# cat /proc/mdstat
Personalities : [raid1]
md2 : active raid1 sdb2[2] sda2[0]
      488279488 blocks [2/1] [U_]
      [=>...................]  recovery =  6.3% (31179264/488279488) finish=91.3min speed=83358K/sec
md1 : active raid1 sdb1[1] sda1[0]
      104320 blocks [2/2] [UU]

unused devices: <none>

HowTo: Reinstate a disk from the RAID1 Array with the command Line

Look at the mdstat

First we must determine which drive is in default.


[root@ ~]#cat /proc/mdstat
Personalities : [raid1] 
md1 : active raid1 sdb1[1] sda1[0]
      104320 blocks [2/2] [UU]
      
md2 : active raid1 sdb2[2](F) sda2[0]
      52323584 blocks [2/1] [U_]
      
unused devices: <none>

(S)= Spare (F)= Fail [0]= number of the disk


Important.png Note:
As we can see the partition sdb2 is in default, we can see the flag: sdb2 [2] (F). We need to resynchronize the disk sdb to the existing array md2.


Fail and remove the disk, sdb in this case

[root@ ~]# mdadm --manage /dev/md2 --fail /dev/sdb2
mdadm: set /dev/sdb2 faulty in /dev/md2
[root@ ~]# mdadm --manage /dev/md2 --remove /dev/sdb2
mdadm: hot removed /dev/sdb2
[root@ ~]# mdadm --manage /dev/md1 --fail /dev/sdb1
mdadm: set /dev/sdb1 faulty in /dev/md1
[root@ ~]# mdadm --manage /dev/md1 --remove /dev/sdb1
mdadm: hot removed /dev/sdb1

Do your Disk Maintenance here

At this point the disk is idle.

[root@ ~]# cat /proc/mdstat
Personalities : [raid1] 
md1 : active raid1 sda1[0]
      104320 blocks [2/1] [U_]
      
md2 : active raid1 sda2[0]
      52323584 blocks [2/1] [U_]
      
unused devices: <none>


Important.png Note:
You'll have to determine if your disk can be reinstated at the array. In fact sometimes a raid can get out of sync after a power failure but also some times for physical outages of the hard disk. It is necessary to test the hard disk if this occurs repeatedly. For this we will use smartctl.


For all the details available by SMART on the disk

[root@ ~]# smartctl -a /dev/sdb

At least two types of tests are possible, short (~ 1 min) and long (~ 10 min to 90 min).

[root@ ~]# smartctl -t short /dev/sdb #short test
[root@ ~]# smartctl -t long  /dev/sdb #long test

to access the results / statistics for these tests:

[root@ ~]# smartctl -l selftest /dev/sdb

You can refer to this page for more information how activate or understand the Analysis and Reporting Technology (SMART) Monitor_Disk_Health


Important.png Note:
if you need to change the disk due to physical failure found by the smartctl command, install a new disk of the same capacity (or more) and enter the following commands to recreate new partitions by copying them from healthy disk sda.


[root@ ~]# sfdisk -d /dev/sda > sfdisk_sda.output
[root@ ~]# sfdisk /dev/sdb < sfdisk_sda.output

GPT Disks

Larger disks will be GPT Disks, sfdisk will not work - you will need to use gdisk and partx (parted)

[root@ ~]# yum install gdisk

The copy the partition table from a good disk to the new disk, the first line will copy the partition table from disk sda to sdd, the second will randomize the GUID

[root@ ~]# sgdisk /dev/sda -R /dev/sdd
[root@ ~]# sgdisk -G /dev/sdd

To view the partitions use partx

[root@ ~]# partx -l /dev/sdd


If you want to reinstate the same disk without replacing it, go to the next step.

Add the partitions back

[root@ ~]# mdadm --manage /dev/md1 --add /dev/sdb1
mdadm: hot added /dev/sdb1
[root@ ~]# mdadm --manage /dev/md2 --add /dev/sdb2
mdadm: hot added /dev/sdb2

Another Look at the mdstat

[root@sme8-64-dev ~]# cat /proc/mdstat
Personalities : [raid1] 
md1 : active raid1 sdb1[1] sda1[0]
      104320 blocks [2/2] [UU]
      
md2 : active raid1 sdb2[2] sda2[0]
      52323584 blocks [2/1] [U_]
      [>....................]  recovery =  1.9% (1041600/52323584) finish=14.7min speed=57866K/sec

unused devices: <none>


Important.png Note:
with a new disk it may be worthwhile to reinstall grub to avoid problems on startup error. The grub is the program that allows you to launch the operating systems. Please enter the following commands.


HowTo: Write the GRUB boot sector

Warning.png Warning:
as the dd command is named "data destroyer" you need to be extremely prudent and sure of the name of source partition and/or destination. At first you should skip the dd command, Step 1 below, and attempt to install grub without it, see Step 2 below. If grub can be installed without using dd, then Step 1 can be discarded.


  • 1.dd
[root@ ~]# dd if=/dev/sda1 of=/dev/sdb1
  • 2.grub
[root@ ~]# grub

    GNU GRUB  version 0.95  (640K lower / 3072K upper memory)

 [ Minimal BASH-like line editing is supported.  For the first word, TAB
   lists possible command completions.  Anywhere else TAB lists the possible
   completions of a device/filename.]

grub> device (hd0) /dev/sdb

grub> root (hd0,0)
 Filesystem type is ext2fs, partition type 0xfd

grub> setup (hd0)
 Checking if "/boot/grub/stage1" exists... no
 Checking if "/grub/stage1" exists... yes
 Checking if "/grub/stage2" exists... yes
 Checking if "/grub/e2fs_stage1_5" exists... yes
 Running "embed /grub/e2fs_stage1_5 (hd0)"...  16 sectors are embedded.
succeeded
 Running "install /grub/stage1 (hd0) (hd1)1+16 p (hd0,0)/grub/stage2 /grub/grub.conf"... succeeded
Done.

grub> quit