Libreswan

	Work in Progress:
	This page is a Work in Progress. The contents off this page may be in flux, please have a look at this page history the to see list of changes.

Credits: John Crisp

About

Openswan is a free implementation of IPsec& IKE for Linux. IPsec is the Internet Protocol Security and uses strong cryptography to provide both authentication and encryption services. These services allow you to build secure tunnels through untrusted networks. Everything passing through the untrusted net is encrypted by the ipsec gateway machine and decrypted by the gateway at the other end of the tunnel.The resulting tunnel is a virtual private network or VPN.

Installation

There are different installation instructions for SME8 and SME9:

SME Server 8

For SME Server 8, at least openswan-2.6.38-1.x86_64.rpm is required. However, this version is not to be found in the default repo's, nor any of the additional repo's. A trusted copy of Openswan for SME8 can be found here. (This is only for 64bit systems!)

After you have downloaded the above file, you can install it by issuing the following command:

yum localinstall openswan-2.6.38-1.x86_64.rpm

SME Server 9

For SME Server 9, the Openswan can be found in the default repo's, so to install Openswan on SME Server 9, simply enter the following command:

yum install openswan

Openswan as a SME Server service

To make the Openswan service start at boot time we need to issue the following commands as root:

ln -s /etc/rc.d/init.d/e-smith-service /etc/rc7.d/S99ipsec
chkconfig ipsec on
config set ipsec service
config setprop ipsec status enabled

This makes ipsec service start at boot time and you can disable/enable the ipsec service at will.

SME Server firewall configuration

Since Openswan/ipsec is all about security and private connections, the SME Server firewall rules play a crucial part of a correct configuration.

We need a new template fragment to allow ipsec through the firewall

touch /etc/e-smith/templates-custom/etc/rc.d/init.d/masq/15AllowIPsec

Add the following code :

# IPsec ports
/sbin/iptables -A INPUT -i $OUTERIF -p udp --sport 500 --dport 500 -j ACCEPT 
/sbin/iptables -t mangle -A PREROUTING -i $OUTERIF -p 50 -j MARK --set-mark 1  
/sbin/iptables -A INPUT -i $OUTERIF -m mark --mark 1 -j ACCEPT 
/sbin/iptables -A FORWARD -i $OUTERIF -m mark --mark 1 -j ACCEPT 
/sbin/iptables -A INPUT -i $OUTERIF -m mark --mark 2 -j ACCEPT 
/sbin/iptables -A FORWARD -i $OUTERIF -m mark --mark 2 -j ACCEPT 
/sbin/iptables -t nat -I POSTROUTING -m policy --dir out --pol ipsec -j ACCEPT 

expand-template /etc/rc.d/init.d/masq
service masq restart

We also need to disable redirects.

	Note:
	The below script will work for SME8 but NOT necessarily for SME9! Since in SME9 the NIC's have no longer fixed names like eth0 and eth1. We need to come up with an auto detect scipt

I have the following code in a file called Disable_Redirects.sh and a link to it in /etc/rc.d/rc.local

#!/bin/bash
# For OpenSwan
# Disable send redirects
echo 0 > /proc/sys/net/ipv4/conf/all/send_redirects
echo 0 > /proc/sys/net/ipv4/conf/default/send_redirects
echo 0 > /proc/sys/net/ipv4/conf/eth0/send_redirects
echo 0 > /proc/sys/net/ipv4/conf/eth1/send_redirects
echo 0 > /proc/sys/net/ipv4/conf/lo/send_redirects
# echo 0 > /proc/sys/net/ipv4/conf/ppp0/send_redirects
# Disable accept redirects
echo 0 > /proc/sys/net/ipv4/conf/all/accept_redirects
echo 0 > /proc/sys/net/ipv4/conf/default/accept_redirects
echo 0 > /proc/sys/net/ipv4/conf/eth0/accept_redirects
echo 0 > /proc/sys/net/ipv4/conf/eth1/accept_redirects
echo 0 > /proc/sys/net/ipv4/conf/lo/accept_redirects
# echo 0 > /proc/sys/net/ipv4/conf/ppp0/accept_redirects

IPSEC server to server configuration

Openswan/IPSEC can be used to setup a secue and permanent VPN connection between a SME Server and another (local or remote) IPSEC enabled device such as a router.

Here is an example:

On the online VPS it has a 'dummy' internal network adaptor but works fine with this.

Here is a sample of my /etc/ipsec.conf with some added notes.

LEFT side is your server. RIGHT side is your router.

# /etc/ipsec.conf
# basic configuration
#auto = 'start' for both ways or 'add' for incoming only

version 2.0 config setup

# Debug-logging controls:  "none" for (almost) none, "all" for lots.
#klipsdebug=none
plutodebug=none
interfaces=%defaultroute
oe=no
protostack=netkey
syslog=syslog.debug
# syslog=syslog.warning
virtual_private=%v4:192.168.0.0/24,   # Here you add the local/internal network of your server
nat_traversal=yes   # if required - probably yes
# Connection settings
# Router to Server
conn draytek-wan1 # Your connection name
type=tunnel
authby=secret
auto=start   # n.b. "auto = start" for ipsec to try and make a connection or "auto = add" to accept incoming
ikelifetime=28800s
keylife=3600s
left=%defaultroute
leftsourceip=192.168.98.1  # This is the IP address of your internal ethernet connection on your server
leftsubnet=192.168.98.0/24 # This is your local network on your server
pfs=yes  # If require
dpdaction=restart
dpddelay=30
dpdtimeout=10
right=1.2.3.4  # This is the WAN IP address of your router that is connecting in
rightsubnet=192.168.0.0/24	# This is the local network behind the router at the far end
# More incoming connections here

Passwords

The following file needs to be looked after and should be set chmod 0600

# /etc/ipsec.secrets
# Format is 
# Incoming_IP Local_IP: PSK "Your#Strong#Password"
1.2.3.4 %any: PSK "Your#Strong#Password"
host.dnsalias.org %any: PSK "Your#Strong#Password"
1.2.3.4 192.168.98.1: PSK "Your#Strong#Password"
%any 192.168.98.1: PSK "Your#Strong#Password"

A reboot should get everything going.

Now set up your router. Create a new IPSEC VPN connection with the correct credentials and it should connect up.

Check /var/log/secure for debug messages, and once you are happy, change the debug settings in ipsec.conf from debug to warning.

If you need more debugging you can set plutodebug = all