Difference between revisions of "Denyhosts"
Unnilennium (talk | contribs) (New page: == Diskusage for SME Server == === Maintainer === [http://smeserver.pialasse.com/ Unnilennium aka Jean-Philippe PIALASSE] (Contrib) === Description === * Denyhosts bans hosts which fail...) |
Unnilennium (talk | contribs) |
||
| Line 1: | Line 1: | ||
| − | = | + | {{Languages|Denyhosts}} |
| + | =Denyhosts SSH for SME7= | ||
=== Maintainer === | === Maintainer === | ||
| Line 24: | Line 25: | ||
3. Instructions at the end of previous installation advices the following commands: | 3. Instructions at the end of previous installation advices the following commands: | ||
<br><code>signal-event post-upgrade and signal-event reboot</code> | <br><code>signal-event post-upgrade and signal-event reboot</code> | ||
| − | <br>but you can skip that | + | |
| + | '''it is recommended to do so !''' | ||
| + | |||
| + | <br>but you can skip that using | ||
| + | /etc/e-smith/events/actions/navigation-conf | ||
4. Open your webbrowser and go to the server-manager. | 4. Open your webbrowser and go to the server-manager. | ||
| Line 30: | Line 35: | ||
You should go to it and configure all necessary allowed host before enabling the service | You should go to it and configure all necessary allowed host before enabling the service | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | Alternatively you can use the server-manager panel "Software installer" to add a new package and select smeserver-denyhosts, instead of steps 1 to 3, then refresh your browser and configure denyhosts, | + | Alternatively you can use the server-manager panel "Software installer" to add a new package and select smeserver-denyhosts (repo smecontribs must be enabled) then do the reconfiguration and reboot task, instead of steps 1 to 3, then refresh your browser and configure denyhosts,. |
Revision as of 04:08, 24 April 2008
Denyhosts SSH for SME7
Maintainer
Unnilennium aka Jean-Philippe PIALASSE (Contrib)
Description
- Denyhosts bans hosts which failed too many login attempts to your ssh deamon.
- It contains also a panel in the server manager to see who is blocked, add some allowed hosts not to block and enable or disable the service.
it needs the packages smeserver-denyhosts and denyhosts
Installation
1. Log in (with username root) to the SMEserver console.
2. Install smeserver-denyhosts
yum install smeserver-denyhosts --enablerepo=smecontribs
You will get a y/N-question, answer y if it looks fine.
3. Instructions at the end of previous installation advices the following commands:
signal-event post-upgrade and signal-event reboot
it is recommended to do so !
but you can skip that using
/etc/e-smith/events/actions/navigation-conf
4. Open your webbrowser and go to the server-manager.
Under "Security" there should be a new line named "SSH Denyhosts".
You should go to it and configure all necessary allowed host before enabling the service
Alternatively you can use the server-manager panel "Software installer" to add a new package and select smeserver-denyhosts (repo smecontribs must be enabled) then do the reconfiguration and reboot task, instead of steps 1 to 3, then refresh your browser and configure denyhosts,.
Uninstall
yum remove smeserver-denyhosts denyhosts
or alternatively just remove them from the server-manager "Software installer"
Additional information
you can change the destination email account, instead of the default admin account, for this contribs using :
config setprop denyhosts AdminEmail youremail@yourdomaine.tld signal-event conf-denyhosts
Check installed version
yum info installed smeserver-denyhosts
